Connection/Terminal Kits
End Seal Kits
End Seal Kits for heating cable in hazardous and non-hazardous locations. Light options are available.
2SC-LTC
This kit is a below insulation end connection kit for Raychem 2SC60, 2SC70 and 2SC80 heating cables. Approved by CSA and FM for use in hazardous locations.
2SC-STC
This kit is a below insulation end connection kit for Raychem 2SC30, 2SC40 and 2SC50 heating cables. Approved by CSA and FM for use in hazardous locations.
3SC-LTC
This kit is a below insulation end connection kit for Raychem 3SC60, 3SC70 and 3SC80 heating cables. Approved by CSA and FM for use in hazardous locations.
E-100
The E-100 kit is an above insulation end seal kit for Raychem BTV, QTVR, XTV, KTV or VPL industrial parallel heating cables.
E-100-L
The E-100-L kit is an above-insulation, lighted end seal kit for Raychem BTV, QTVR, XTV, KTV or VPL industrial parallel heating cables.
E-100-LBTV2
The E-100-LBTV2 is a NEMA-4X rated end seal kit for use with Raychem LBTV2-CT heating cable. The kit is FM approved and CSA certified for use in division 2 hazardous locations. The kit utilizes a sealant-filled boot and is easily re-entered for maintenance.
E-150
The E-150 is a cold-applied low-profile end seal.
H912: End Seal Kit
The WinterGard H912 is a gel-filled end seal kit available for use with all WinterGard heating cables. Each kit includes two end seals.
HAK-JB3-100
The HAK-JB3-100 is an explosion-proof, corrosion-resistant junction box that serves as a power connection, splice, tee, or end termination. Must be ordered separately.
RayClic-E
Lighted end seal kits are installed wherever an end-of-line signal light is required. Each kit contains one RayClic-LE lighted end seal and one RayClic-SB-04 pipe-mounting bracket.
SC-JBE-L
This kit is an above insulation end connection kit for Raychem 2SC60, 2SC70, 2SC80 and 3SC60, 3SC70, 3SC80 heating cables. Approved by CSA, FM and IEC for use in hazardous locations.
SC-JBE-S
This kit is an above insulation end connection kit for Raychem 2SC30, 2SC40, 2SC50 and 3SC30, 3SC40, 3SC50 heating cables. Approved by CSA, FM and IEC for use in hazardous locations.
Power Kits
Power Connection Kits for heating cable in hazardous and non-hazardous areas.
1SC-12PT
This kit is a below insulation power connection kit for Raychem 1SC30, 1SC40, 1SC50 heating cables. Approved by CSA for use in non-hazardous locations.
1SC-4-6-8PT
These kits are below insulation power connection kits for use with Raychem 1SC60, 1SC70 and 1SC80 heating cables as outlined below. They are approved for use by CSA in hazardous locations. (1SC-4PT 1SC80, 1SC-6PT 1SC70, 1SC-8PT 1SC60)
2SC-12PT
This kit is a below insulation power connection kit for Raychem 2SC30, 2SC40 and 2SC50 heating cables. Approved by CSA and FM for use in hazardous locations.
2SC-4-6-8PT
These kits are below insulation power connection kits for Raychem 2SC60, 2SC70 and 2SC80 heating cables as outlined below. They are approved by CSA and FM for use in hazardous locations. (2SC-4PT 2SC80, 2SC-6PT 2SC70, 2SC-8PT 2SC60)
3SC-12PT
This kit is a below insulation power connection kit for Raychem 3SC30, 3SC40 and 3SC50 heating cables. Approved by CSA and FM for use in hazardous locations.
3SC-4-6-8PT
These kits are below insulation power connection kits for Raychem 3SC60, 3SC70 and 3SC80 heating cables as outlined below. Approved by CSA and FM for use in hazardous locations. (3SC-4PT 3SC80, 3SC-6PT 3SC70, 3SC-8PT 3SC60)
9800
The Frostex 9800 FlexFit kit provides the specially designed plug you need to plug one Frostex Plus heating cable into an electrical outlet.
EMK-XP
The EMK-XP power connection/end seal kit provides power to Raychem Electro Melt heating cables.
ETK-XP
The ETK-XP power connection/end seal kit provides power to Raychem Electric Thermal Storage heating cables.
FTC-P
The FTC-P Power Connection and End Seal Kit is for use with XL-Trace, Raysol, and Ice Stop heating cables. Materials for one power connection and one end seal are included in each kit.
FTC-XC
The FTC-XC Power Connection and End Seal Kit is for use with XL-Trace, -CR, and -CT, and Raysol heating cables installed in conduit.
H900
This WinterGard H900 power connection kit is for use in pipe-heating and roof & gutter de-icing applications.
H908: Plug-In Power Connection Kit with GFI
This WinterGard H908 plug-in power connection kit is for use in pipe heating and roof & gutter de-icing applications. The H908 is a plug-in, ground-fault-protected power connection kit.
HAK-C-100
The HAK-C-100 connection system serves as a component for power connection, splice, tee, or end termination with the HAK-JB3-100.
HAK-JB3-100
The HAK-JB3-100 is an explosion-proof, corrosion-resistant junction box that serves as a power connection, splice, tee, or end termination. Must be ordered separately.
JBM-100
The JBM-100 kit serves as a power connection, splice, or tee for up to three Raychem BTV, QTVR, XTV, KTV, or VPL industrial parallel heating cables.
JBM-100-LBTV2
The JBM-100-LBTV2 is a NEMA-4X rated connection kit with 6 AWG terminal blocks for use with Raychem LBTV2-CT heating cable. The kit is FM approved and CSA certified for use in division 2 hazardous locations.
JBS-100
The JBS-100 kit is designed to connect power to a single Raychem BTV, QTVR, XTV, KTV, or VPL industrial parallel heating cable. Approved by FM, CSA and PTB for use in hazardous locations.
JBS-100-ECP-A
The JBS-100-ECP-A is a power connection/electronic controller combination for Raychem Polymeric® and Pyrotenax® MI cables.
JBS-100-ECW-A
The DigiTrace JBS-100-ECW-A is an electronic temperature controller that provides accurate control for all heating cables.
RayClic-PC
A RayClic-PC can supply power to one heating cable. Each kit contains one RayClic-PC power connection, one RayClic-E end seal, and one SB-04 pipe-mounting bracket. The kit includes 5-foot power lead wires and conduit fitting. The junction box and flexible conduit required to make a complete connection are not included.
RayClic-PS
A RayClic-PS can be used as a power connection kit for supplying power to two heating cables. Each kit contains one RayClic-PS powered splice connection, two RayClic-E end seals, and one SB-04 pipe mounting bracket. The kit includes 5-foot power lead wires and conduit fitting. The junction box and flexible conduit required to make a complete connection are not included.
RayClic-PT
A RayClic-PT can be used as a power connection kit for supplying power to three heating cables. Each kit contains one RayClic-PT powered tee connection, three RayClic-E end seals, and one SB-04 pipe-mounting bracket. The kit includes 5-foot power lead wires and conduit fitting. The junction box and flexible conduit required to make a complete connection are not included.
SC-JBP-L
This kit is an above insulation power connection kit for Raychem 2SC60, 2SC70, 2SC80 and 3SC60, 3SC70, 3SC80 heating cables. Approved by CSA, FM and IEC for use in hazardous locations.
SC-JBP-S
This kit is an above insulation power connection kit for Raychem 2SC30, 2SC40, 2SC50 and 3SC30, 3SC40, 3SC50 heating cables. Approved by CSA, FM and IEC for use in hazardous locations.
Splice Kits
Splice kits for self-regulating and variable power-limiting heating cables, available for use in hazardous and non-hazardous locations.
1SC-SSC
This kit is a below insulation splice connection kit for Raychem 1SC30, 1SC40, 1SC50, 1SC60, 1SC70 and 1SC80 heating cables. Approved by CSA for use with 1SC30, 1SC40, 1SC50 in non-hazardous locations and with 1SC60, 1SC70, 1SC80 in hazardous locations.
2SC-LSC
This kit is a below insulation splice connection kit for Raychem 2SC60, 2SC70 and 2SC80 heating cables. Approved by CSA and FM for use in hazardous locations.
2SC-SSC
This kit is a below insulation splice connection kit for Raychem 2SC30, 2SC40 and 2SC50 heating cables. Approved by CSA and FM for use in hazardous locations.
3SC-LSC
This kit is a below insulation splice kit for Raychem 3SC60, 3SC70 and 3SC80 heating cables. Approved by CSA and FM for use in hazardous locations.
3SC-SSC
This kit is a below insulation splice kit for Raychem 3SC30, 3SC40 and 3SC50 heating cables. Approved by CSA and FM for use in hazardous locations.
3SC-STC
This kit is a below insulation splice kit for Raychem 3SC30, 3SC40 and 3SC50 heating cables. Approved by CSA and FM for use in hazardous locations.
EMK-XS
The EMK-XS termination and splicing components are used to terminate the end of the heating cable to power conductors or to splice one length of heating cable to another.
FTC-HST
The FTC-HST is used with RaySol System heating cables to make splice connections (on slab bottoms only), and with IceStop and XL-Trace Systems to make splice and tee connections.
H910: Splice & Tee Kit
The WinterGard H910 is a splice & tee kit available for use with all WinterGard heating cables.
HAK-C-100
The HAK-C-100 connection system serves as a component for power connection, splice, tee, or end termination with the HAK-JB3-100.
HAK-JB3-100
The HAK-JB3-100 is an explosion-proof, corrosion-resistant junction box that serves as a power connection, splice, tee, or end termination. Must be ordered separately.
JBM-100
The JBM-100 kit serves as a power connection, splice, or tee for up to three Raychem BTV, QTVR, XTV, KTV, or VPL industrial parallel heating cables.
RayClic-S
RayClic-S splice kits are installed as needed to connect two heating cables together at one point. Each kit contains one RayClic-S splice.
S-150
The S-150 is a cold-applied, low profile splice for in-line connection.
SC-JBS-L
This kit is an above insulation power connection kit for Raychem 2SC60, 2SC70, 2SC80 and 3SC60, 3SC70, 3SC80 heating cables. Approved by CSA, FM and IEC for use in hazardous locations.
SC-JBS-S
This kit is an above insulation splice connection kit for Raychem 2SC30, 2SC40, 2SC50 and 3SC30, 3SC40, 3SC50 heating cables. Approved by CSA, FM and IEC for use in hazardous locations.
T-100
The T-100 serves as an above-insulation splice or tee kit for up to three Raychem BTV, QTVR, XTV, KTV, or VPL industrial parallel heating cables. Approved by FM, CSA and PTB for use in hazardous locations.
Tee Kits
Tee kits for self-regulating and variable power-limiting heating cables.
FTC-HST
The FTC-HST is used with RaySol System heating cables to make splice connections (on slab bottoms only), and with IceStop and XL-Trace Systems to make splice and tee connections.
H910: Splice & Tee Kit
The WinterGard H910 is a splice & tee kit available for use with all WinterGard heating cables.
HAK-C-100
The HAK-C-100 connection system serves as a component for power connection, splice, tee, or end termination with the HAK-JB3-100.
HAK-JB3-100
The HAK-JB3-100 is an explosion-proof, corrosion-resistant junction box that serves as a power connection, splice, tee, or end termination. Must be ordered separately.
JBM-100
The JBM-100 kit serves as a power connection, splice, or tee for up to three Raychem BTV, QTVR, XTV, KTV, or VPL industrial parallel heating cables.
RayClic-T
RayClic-T kits are installed as needed to connect three heating cables together at one point. Each kit contains one RayClic-T tee connection and one RayClic-E end seal.
RayClic-X
RayClic-X cross kits are installed as needed to connect four heating cables together at one point. Each kit contains one RayClic-X cross and two RayClic-E end seals.
T-100
The T-100 serves as an above-insulation splice & tee kit for up to three Raychem BTV, QTVR, XTV, KTV, or VPL industrial parallel heating cables. Approved by FM, CSA and PTB for use in hazardous locations.